∅The realization of 4.5mx6m overflow ball mill electric control system

By -

Overflow https://clactononseaessex.uk are widely used in cement, mining and thermal power generation industries due to their simple operation and low maintenance costs. With the development of society, the ball mill has made great progress in overall performance. The ball mill electrical control system is the central system of the entire ball mill, used to control various operating techniques.

  The control system mainly includes:

(1) Control of temperature measurement of bearings and stator windings;

Each mill has three temperature measurement points for the main bearing at the feed end, the main bearing at the discharge end and the stator winding of the main motor, and the pinion bearing and the main motor have two temperature measurement points. At the same time, the status value of each point can be displayed in real time on the man-machine interface connected to the PLC, and the alarm value and shutdown value of each measurement point can be given.

(2) Control of the main bearing high and low pressure lubrication station

   The main bearing high and low pressure lubrication station includes high pressure oil supply and low pressure lubrication. The high pressure oil supply system of each station supplies two high pressure pump motors. When any high pressure pump fails to work or the oil pressure is low, the backup pump will automatically replace the original work. The pump works and continues to supply oil to the main bearing.

(3) Pressure control

The high-pressure system of the lubrication station is equipped with four pressure sensors to detect the high-pressure oil supply system in real time. When the oil pressure is lower than the lower limit setting value, the sensor will send out an audible and visual alarm signal and limit the start of the host; when it is higher than the upper limit value When the sensor will send out an audible and visual alarm signal.

(4) Oil flow control

Install a flow switch in the low pressure oil supply system near the two main bearing oil supply points to continuously monitor the oil supply flow at each point.

(5) Oil temperature control

There is no electric heater or cooler on the lubrication station, and the oil temperature is given an obvious display signal by the bimetal thermometer through the electric control system to automatically turn on the electric heater or the cooling water valve.

(6) Control of slow drive motor

The slow-speed drive motor and the main motor are interlocked with each other, and they cannot work at the same time; when the slow-speed drive motor is working, the high-voltage oil supply system should be in a normal working state.

Comments

Post a Comment

Popular posts from this blog

Selection of spodumene flotation reagents

By -
Image
At present, the  beneficiation methods of spodumene  mainly include: manual separation, thermal disintegration, magnetic separation, resuspension method,  flotation method  and combined beneficiation method. Among them, the flotation method of spodumene is the most studied in the laboratory and the most widely used mineral processing method in industry. 1. Cationic collectors The cationic collectors used in the flotation of spodumene ore are mainly amine collectors, which flotate gangue minerals such as quartz, feldspar and mica under acidic conditions, and leave the spodumene at the bottom of the tank. This method is often used in the roughing of spodumene, and cannot directly obtain spodumene concentrate with higher purity, and needs to be used in conjunction with other sorting methods. In production practice, Yan Gengsheng used  the process of flotation of spodumene  with mixed soap and diesel oil under alkaline conditions after flotation of mica with phylloylamine under acidic cond
Read more

How to use inclined plate thickener for tailings dry discharge

By -
Image
 Tailings treatment is an important part of mine production. Concentration in dry tailings discharge is an important link in achieving dry stacking. It not only directly affects the processing capacity of filter equipment, but also affects the resistance of filter cakes. The particle is resistive to the filter cake, so according to the characteristics of iron tailings, there is a new type of thickener . The flow of tailings slurry in the thickener is ideally slow. As soon as the solid particles leave the flow layer, they will be considered as sediment. This model is also called shallow sedimentation. The sedimentation occurs in the void between the inclined plates. Within the cavity, but due to the small spacing between the inclined plates, it creates favorable conditions for the formation of laminar flow. The clarified overflow water moves upward along the inclined plate space, and the solid particles settle between the two plates, and only need to settle to a small distance to fall o
Read more

A new type of coarse particle flotation machine for rough grinding and flotation in mines

By -
 Coarse ore flotation has always been one of the key technologies for mine coarse grinding and flotation to reduce energy consumption. An iron ore plant in Anhui Province has a very small content of mica in the iron ore of the first grinding product. Recovery value. However, there are generally two ways to recover mica at present: one is coarse-grained regrind and reselection; the other is to choose equipment suitable for coarse-grained mineral flotation. However, during the inspection of the production site, it was found that many of the mica minerals in the second-stage grinding products in this iron ore did not meet the particle size requirements of flotation, and the density of mica was small, and most of them showed flaky structure. The overflow of the cyclone ran out, causing the inspection and screening operation to be blocked first, so regrinding is not suitable for the recovery of coarse mica.     The design principle of coarse-grained flotation machine is that coarse-grained
Read more